Centerbeams other than socalwb909's

[stouthm]

Hope this is the correct section, if not, please move. I really like socalwb909's centerbeams BUT you can only load what he has put in the config file. I would like to load other 16ft lumber (2:30671:94407101:1) only because there are scenery items for that kuid which I can place around the loading area. That product doesn't fit on his centerbeams. There only two other centerbeams by msgsapper that are available but they look really bright. Any one know of other centerbeams out there for TRS12? Thanks.

Here's an opening for some creator. There's a need for more centerbeams like cnr made awhile back. Hint, hint.

 

[Dermmy]

cnr has some oldies but goodies at TPR's Download Depot...

 

[stouthm]

Andy, thanks for checking in but I have all of cnr's but they don't work in TRS12. I'm not into that phase of this sim, fixing things, but I'm getting close if I want things to work in TRS12. We shouldn't have to do this but that's another subject. Might have to check out PEV's programs.

 

[danny5]

When you click the ? mark and then the car,your list of product comes up ! Now remove all the products. Where the amont for that car is now can be changed to what will make it more of a full load. If it's 32 and it looks half full change it to 64 add your lumber 16ft. If not full enought change to 68,if to full make it smaller. Remember you have to remove the lumber to change it again.

 

[stouthm]

danny5, thanks for responding. In theory it should work but after trying many different combinations it doesn't. I think it may have to do with the product load points or something like that. Not an area I want to be messing around with. I'm using msgsapper's for now. Thanks again.

 

[danny5]

Did you try the 2nd quene? The loading points are in difference places and setting the max to 40 the car loads fine, lumber is centered and right at the top.

 

[stouthm]

No, but I'll give it a try.

 

[stouthm]

Randy, just want to make sure that we're comparing apples with apples here. I tried different configerations and had no luck. Looking at the screenshot from left to right the first load is queue 1, max load 15, 10 units. Second load is queue 2, max load 20, 18 units, third load is queue 3, max load 25, 16 units and the fourth load is queue 4, max load 24, 24 units. If you notice the first three loads all extend beyond the bulkhead. The fourth load is much higher than the centerbeam running down the middle of the car. The product I'm trying to load is kuid2:30671:94407101:1 which belongs to llj. If you can show me something that fits that would be greatly appreciated.

 

[slabay]

Randy, just want to make sure that we're comparing apples with apples here. I tried different configerations and had no luck. Looking at the screenshot from left to right the first load is queue 1, max load 15, 10 units. Second load is queue 2, max load 20, 18 units, third load is queue 3, max load 25, 16 units and the fourth load is queue 4, max load 24, 24 units. If you notice the first three loads all extend beyond the bulkhead. The fourth load is much higher than the centerbeam running down the middle of the car. The product I'm trying to load is kuid2:30671:94407101:1 which belongs to llj. If you can show me something that fits that would be greatly appreciated.

Search the DLS for username Yukonzoom. He's got a TON of lumber products available in all kinds of lengths in loads and as scenery objects.

 

[danny5]

In the 2nd quene did you change the load amount to 40? Remember that you have to remove all products, change the load amount to 40 then add your lumber.

 

[stouthm]

danny5, no luck. The product I want to use is 4' x 16' and none of the queues matches up to that. Believe me, I've tried many different combinations.

slabay, I couldn't find any lumber scenery for Yukonzoom's lumber loads. I use a lot of his items so I was aware of him. Thanks for checking in.

So tomorrow I'm heading for the Jersey shore for a week in the sand and surf with 6 of my 9 grandchildren. All in one house on the beach. Looking forward to it. Will be back on the forum in a week. Thanks everyone.

 

[slabay]

I couldn't find any lumber scenery for Yukonzoom's lumber loads. I use a lot of his items so I was aware of him. Thanks for checking in.

::gasp:: You're right! Now that I pulled them up in the Content Mangler, he does not have non-load versions of the lumber. I thought he did.