Heinrich505
Active member
Has anyone had problems with sessions from the Mojave Subdivision payware from TANE? I am running TANE SP2 and have run into some odd difficulties.
For Session DPU Push:
I start out in Cab Mode, with two pusher engines waiting on the siding. The long train comes by and stops just past the siding. I drive the pushers out and couple to the rear of the train. Cab mode is working just fine. Now I am directed to go to the front and drive the entire train. I do this, and then cannot get the train to move, no matter how much throttle or sanders or anything. The train won't budge, even at notch 8. The engines just overheat. I made sure the brakes were dumped, hitting D many times and seeing they were cleared. The engines won't pull the train. It is almost as if the rolling stock all have brakes on. Very odd.
However, if I switch over to DCC, the train moves just fine, and accelerates smoothly as power is applied, with no problems. Strange.
I tried to switch back to Cab Mode while the consist was moving. The train then slowly starts braking and comes to a halt, even though I am applying throttle. Brakes are not on at all, but the train comes to a halt. I switch back to DCC and once more the train smoothly accelerates.
So, I run the session in DCC, as it is the only way the train will move. But, partway through the session, I have to stop the train and cut off the first three coal cars, putting them on a siding. I stop the train, uncouple the cars from the main body, and, for the heck of it, I put it back to Cab Mode. Works fine. I pull the three cars around, back them onto the siding, and uncouple them, all using Cab Mode. I then pull off the siding, back up to the main consist, recouple, and cannot move the blasted thing, just as before. A switch back to DCC, and off I go, no problems once more. The same thing happens at the end of the session, when I cut the two pushers off the end of the train. I put it back in Cab Mode and the two engines worked just fine, stabled on a spur with no problems, all while in cab mode.
Once done with the session, I tried to access my saved games from the session and the game crashed to desktop. This happened for every save I had for the DPU session (5 total). This also happened for every save I had on another session, the ATSF #991 East session (2 saves). I can access the start of the game for both sessions, but any attempt to open the saved games results in me getting thrown completely out of the game.
So, anyone else have problems of this sort with the Mojave Subdivision?
Heinrich505
For Session DPU Push:
I start out in Cab Mode, with two pusher engines waiting on the siding. The long train comes by and stops just past the siding. I drive the pushers out and couple to the rear of the train. Cab mode is working just fine. Now I am directed to go to the front and drive the entire train. I do this, and then cannot get the train to move, no matter how much throttle or sanders or anything. The train won't budge, even at notch 8. The engines just overheat. I made sure the brakes were dumped, hitting D many times and seeing they were cleared. The engines won't pull the train. It is almost as if the rolling stock all have brakes on. Very odd.
However, if I switch over to DCC, the train moves just fine, and accelerates smoothly as power is applied, with no problems. Strange.
I tried to switch back to Cab Mode while the consist was moving. The train then slowly starts braking and comes to a halt, even though I am applying throttle. Brakes are not on at all, but the train comes to a halt. I switch back to DCC and once more the train smoothly accelerates.
So, I run the session in DCC, as it is the only way the train will move. But, partway through the session, I have to stop the train and cut off the first three coal cars, putting them on a siding. I stop the train, uncouple the cars from the main body, and, for the heck of it, I put it back to Cab Mode. Works fine. I pull the three cars around, back them onto the siding, and uncouple them, all using Cab Mode. I then pull off the siding, back up to the main consist, recouple, and cannot move the blasted thing, just as before. A switch back to DCC, and off I go, no problems once more. The same thing happens at the end of the session, when I cut the two pushers off the end of the train. I put it back in Cab Mode and the two engines worked just fine, stabled on a spur with no problems, all while in cab mode.
Once done with the session, I tried to access my saved games from the session and the game crashed to desktop. This happened for every save I had for the DPU session (5 total). This also happened for every save I had on another session, the ATSF #991 East session (2 saves). I can access the start of the game for both sessions, but any attempt to open the saved games results in me getting thrown completely out of the game.
So, anyone else have problems of this sort with the Mojave Subdivision?
Heinrich505