What is missing here?

B

boc61

New member
This is from the BNSF Clovis Sub 2

2n8bi9y.jpg


Evidently there is some part of this bridge missing, but I can't figure it out. I'm not sure I've even identified it properly as if I put down a new one it looks fine. I'm not showing any missing or faulty assets in CM. This is at the beginning of the route headed toward California. Anybody have this route installed and can shed some light on it? I guess I can replace the bridge, but it is puzzling.
 
On my laptop at the moment, will look shortly. This is near Belen I'm guessing, looks like it's missing the bridge deck.
 
fran1 said:
On my laptop at the moment, will look shortly. This is near Belen I'm guessing, looks like it's missing the bridge deck.
Click to expand...

If it's next to California portal, it's JJS Plate Girder, kuid 46819:38123. Your also missing a stream and telegraph poles by the look of it.
 
fran1 said:
If it's next to California portal, it's JJS Plate Girder, kuid 46819:38123. Your also missing a stream and telegraph poles by the look of it.
Click to expand...

No its not, just checked
That KUID # is a built in
and it is a single track
 
Last edited:
Just to let you know I'm DL C-sub 2.1 now!
Installing now!
Looking..........Get back soon...

Well this is weird,in my case I have the center but not the ends.
I have fixed this kind of weirdness before.
Got to fire up AssetX, be back in one hour.

Gerry
 
Last edited:
xcrossi said:
I know how to fix that but I have to have the same bridge.
Any way to post that kuid number.
Click to expand...

I "think" it's the kuid in the picture, but I'm not sure. I can't grab anything with any certainty, sometimes it shows the bidge as in the picture, sometimes it shows the track. Sometimes I get a sort of sidewalk spline. I don't know what the bridge pilings are either, I can't grab those. If I delete the track on either side, some of the pilings, but not all go as well leaving the railess track and a couple of remaining pilings. I know this is an old route, could that have anything to do with it?
 
I suspect the asset is missing a mesh file. Your config should look like this...
The bridge track is at you discretion. I'm using one of JRs' tracks in this config.


kuid <kuid:46819:38123>
username "JJS_Plate_Girder"
kind "bridge"
length 28.3
height -1.1
istrack 1
isroad 0
bendy 1
width 7.1
rgb 200,100,0
repeats 1
trackoffsets 0.01
trackdirections 0,1
bridgetrack <kuid:35412:38111>
category-class "TB"
category-region "US"
category-era "2000s"
trainz-build 2.9
obsolete-table
{
}
thumbnails
{
0
{
image "preview.jpg"
width 240
height 180
}
}
mesh-table
{
default
{
mesh "jjs_plate_girder.im"
auto-create 1
}
}
kuid-table
{
0 <kuid:35412:38111>
}

-AL
 
This seems to be another SP1 problem. The bridge shows up as it should be in my version which is still at build 49922.





I did open it for edit in CMP which makes it show some warnings but by reverting to original the warnings are hidden.

Cheers,
Bill69
 
That center support is a separate asset.
Bridge Support #2 OLD Stone, single track
Kuid2:124017:30013:1
Therefore the abutments must be a different asset.
Just haven't found them yet.
 
Ok I did some playing with this and here is what I've ascertained: The supports are separate items as Gerry said. That track is from JJS Deck Girder Bridge kuid:46819:38129. The deck is missing, why I don't know and why I don't get an error on it. The bridge Bill shows is JJS Plate girder, which looks to be a workable substitute ao I will use that. I hoped to just use Replace assets but I've learned you can use it for bridges so I guess I'll just do it through CM. I have about 5 other routes that use that bridge so it's get swapped out for all of them. I dunno why the deck won't show, but it's no big deal now.

I just reread the thread and maybe GP30 had the answer, a missing mesh file? I'm going to have a look and compare the two bridges files.
 
Last edited:
This is the config in 2010 native for a comparison.

Wrong bridge, back in a moment.

Right bridge now.

kind "bridge"
type "Bridges"
length 28.3
height -1.1
istrack 1
isroad 0
bendy 1
width 7.1
rgb 200,100,0
repeats 1
carrate 35
trackoffsets 0.01
bridgetrack <kuid:35412:38111>
region "JJS"

obsolete-table
{
}
trainz-build 1.3
category-region-0 "to"
category-era-0 2000
asset-filename "JJS_Plate_Girder"
name
category-class "TB"
kuid <kuid:46819:38123>
description "l"
username "JJS_Plate_Girder"
thumbnail
author
organisation
contact-email
contact-website
license

kuid-table
{
0 <kuid:35412:38111>
}
username-pl "JJS_Wspornik_Płytowy"
username-cz "JJS_deskové_nosníky"
description-es "L"

There is an jjs plate girder IM file and a rusty2 texture which are not refered to in the config.
 
Last edited:
This is what I did to make it finely show.
In the backup folder delete all reference to that bridge.

I did not change build number

Edit original bridge file /name"" to name"anything" commit.
kuid <kuid:46819:38129>
username "JJS_Deck_Girder"
kind "bridge"
trainz-build 1.3
type "Bridges"
length 4
height -3.006
istrack 1
bendy 1
width 3
rgb 200,100,0
repeats 1
trackoffsets 0.01
bridgetrack <kuid:35412:38051>
region "JJS"

obsolete-table
{
}
category-region-0 "to"
category-era-0 2000
asset-filename "JJS_Deck_Girder"
name "gerry"
category-class "TB"
description "l"
author
license
organisation
contact-website
contact-email

kuid-table
{
0 <kuid:35412:38051>
}


The bridge ends are actuality 8 single track assets of the same type.
I still can't find them
 
You must log in or register to reply here.

Similar threads

C
Looking To Fix A Locomotive With Missing Bogies
Replies
5
Views
685
p-dehnert
P
H
Missing asset box appears even though asset is installed
Replies
2
Views
127
stagecoach
S
R
Trainz Height (Revisited)
Replies
4
Views
729
rick1958
R
P
Updating old double track and bridges
Replies
8
Views
1K
Pendolino
P
C
Looking For A Missing Asset For SI3D's IoS - Kellsthorpe Extension Route
Replies
2
Views
601
ChugLifeBoy
C
Back
Top