Portal Emitting Driverless Train

[Jaykob8]

Hi,

I am having issues with using traffic control from portals directly (where I enter the properties on the portal) while trying to make traffic for a session on Pagroove's Electro Island involving the Shinkansen trains. Usually, I edit properties of a portal. The Northtropp CS Production portal works perfectly, but the CS Shin Hanyo Production portal seems to have some issues as it produces "glitched" trains with no driver. Is there a reason to this? I assigned drivers to all train outputted trains, even at Shin Hanyo, but there is always that glitch.

 

[JCitron]

What portals are you using?

There's an issue with the small Portal Basic. The large-sized Portal Basic works fine.

 

[Jaykob8]

Yeah. It's the small size portal, but it's only from one side. I don't know what's happening. Is there a way to fix this?

 

[Jaykob8]

What portals are you using?

There's an issue with the small Portal Basic. The large-sized Portal Basic works fine.

It isn't happening in the Icarus Shinkansen, it's just with only one of the Electro Island portals. I don't understand.

 

[JCitron]

It isn't happening in the Icarus Shinkansen, it's just with only one of the Electro Island portals. I don't understand.

Check the direction of the consists within the portal - you need to do this in the session and not the route.
If you have to, change out the portals to the ones that work.

 

[Jaykob8]

I'm putting them in a trainset (where almost every train is facing forward except the back power car) and I'm doing this in the session.

 

[JCitron]

I'm putting them in a trainset (where almost every train is facing forward except the back power car) and I'm doing this in the session.

Make sure that forward is to the left. There is no way for a consist to flip around prior to exiting. I have never seen that unless the issue was self inflicted.

 

[Jaykob8]

Make sure that forward is to the left. There is no way for a consist to flip around prior to exiting. I have never seen that unless the issue was self inflicted.

What do you mean "to the left"? The train is facing "to the left". I even tried using an "un-portal" rule at Shin Hanyo production trackmark and it partially worked until the production of the JR 500 Nozomi and N700. What is going on?

 

[JCitron]

What do you mean "to the left"? The train is facing "to the left". I even tried using an "un-portal" rule at Shin Hanyo production trackmark and it partially worked until the production of the JR 500 Nozomi and N700. What is going on?

Is it only those consist thats have that issue?

The consists are facing the correct way.

 

[Jaykob8]

Is it only those consist thats have that issue?

The consists are facing the correct way.

They are 100% facing the correct way. I checked multiple times, reset the portal and readded the drivers and the trainsets and they are not working at all.

 

[JCitron]

They are 100% facing the correct way. I checked multiple times, reset the portal and readded the drivers and the trainsets and they are not working at all.

Have you tried other trainsets. Try anything other than the ones you are working such as a built-in American diesel pulled trainset to see if that comes out backwards. The portals on my routes work fine, FYI.

 

[Jaykob8]

I've tried the 0 series Shinkansen and 700 RS and they work fine when I use the Un-Portal (assuming I should use that). However, the 500 and N700 ones don't. I tried the 0 and 700 RS with the normal, and it didn't (at the Shin Hanyo one), but worked perfectly at the Northtropp one. Maybe you should download the route and make a session with Colden Shinkansens emitting from both ends every 8 minutes. It's pagroove's Electro Island 5.0.