BUILD 100240.
I have an EIT Tower "Enhanced TRC3 invisible Interlocking Tower (SP2 and later)" <KUID2:61392:8101:52>
I have 2 rails running past a single rail station. (one rail is station, the other is a bypass). There are double slips off to each side of the station for crossover needs.
https://www.trainzportal.com/mytrainz/view_media_post?media_post_id=140686 <--Pic of slips with paths in yellow. East and west slips are exactly the same and configured the same.
-----------<S-/-\-S>---TI----------Bypass--TCD-------------TI------<S-/-\-S>----------
-----------<S/---\S>---TI----------Station--TCD-------------TI------<S/---\S>----------
This is shown with North up.
KEY:
S = Signal
<or> = Signal Direction
TI = Track insulator
TCD = Track Circuit Detector
/or\ = Slipover
--- = Track line
I have 8 paths on one tower.
West crossover has "EB STN INBOUND" "EB BYPASS INBOUND" "WB STN OUTBOUND" "WB BYPASS OUTBOUND"
East crossover has "EB STN OUTBOUND" "EB BYPASS OUTBOUND" "WWB STN INBOUND" ""WB BYPASS INBOUND"
No paths are set along the middle section, I have only the TCB setup there.
I'd give a screenshot of the exact problem, But the menu is not in the snapshots I tried to get.
I have one TCD named "Bypass", The other is named "Station". When ran in driver, I get a hold up where a train does not activate certain paths because the RM data says a path TCB is occupied. Going back to surveyer, the affected paths are somehow identifying either both TCDs for a path, or the same TCD twice. I have even gone as far as deleting the TCDs, checking to see that it clears from the tower, then reinstall the TCDs with slightly modified names to be sure, Problem is persistant and I cannot figure out why Some paths are seeing the same TCD twice or both TCDs at once.
I have an EIT Tower "Enhanced TRC3 invisible Interlocking Tower (SP2 and later)" <KUID2:61392:8101:52>
I have 2 rails running past a single rail station. (one rail is station, the other is a bypass). There are double slips off to each side of the station for crossover needs.
https://www.trainzportal.com/mytrainz/view_media_post?media_post_id=140686 <--Pic of slips with paths in yellow. East and west slips are exactly the same and configured the same.
-----------<S-/-\-S>---TI----------Bypass--TCD-------------TI------<S-/-\-S>----------
-----------<S/---\S>---TI----------Station--TCD-------------TI------<S/---\S>----------
This is shown with North up.
KEY:
S = Signal
<or> = Signal Direction
TI = Track insulator
TCD = Track Circuit Detector
/or\ = Slipover
--- = Track line
I have 8 paths on one tower.
West crossover has "EB STN INBOUND" "EB BYPASS INBOUND" "WB STN OUTBOUND" "WB BYPASS OUTBOUND"
East crossover has "EB STN OUTBOUND" "EB BYPASS OUTBOUND" "WWB STN INBOUND" ""WB BYPASS INBOUND"
No paths are set along the middle section, I have only the TCB setup there.
I'd give a screenshot of the exact problem, But the menu is not in the snapshots I tried to get.
I have one TCD named "Bypass", The other is named "Station". When ran in driver, I get a hold up where a train does not activate certain paths because the RM data says a path TCB is occupied. Going back to surveyer, the affected paths are somehow identifying either both TCDs for a path, or the same TCD twice. I have even gone as far as deleting the TCDs, checking to see that it clears from the tower, then reinstall the TCDs with slightly modified names to be sure, Problem is persistant and I cannot figure out why Some paths are seeing the same TCD twice or both TCDs at once.