Crap Sw1500 by Don49PLM

[railroy19]

Missing a kuid for your sw1500.
The number is 387111:100268
The other engine works fine but the 1500 won't load.
These look like very nice engines and the strobe light is very nice feature.

Thanks for nice content.
Bob

 

[fran1]

Missing a kuid for your sw1500.
The number is 387111:100268
The other engine works fine but the 1500 won't load.
These look like very nice engines and the strobe light is very nice feature.

Thanks for nice content.
Bob

Suggest it's a typo, should read 286

 

[railroy19]

Thanks
Are you saying I can fix the config file to fix this engine?

 

[railroy19]

Has anyone been able to get these engines loaded?

I've downloaded them several times and still will not show up in surveyor.

Bob

 

[NSWGR_46Class]

Suggest it's a typo, should read 286

another typo its 228

 

[Euphod]

Has anyone been able to get these engines loaded?

Hi Bob, I just downloaded, installed and took a ride on this piece of Crap:


<kuid2:387111:100228:1>

 

[masterowner]

No curses should be used on this forum please.

 

[Euphod]

"Piece of Crap" is not a curse; it's a piece of Careton Rapids and Pottash(CRAP) equipment.

Nice try though, turnabout is fair play. Good luck to you.

 

[railroy19]

Ahwright!! Ed

I have about three hours into trying to get these Sw1500' s to load up.
Did you change the kuid #? I'm going to try that out right now let you know how I make out.

Thanks Buddy.

 

[railroy19]

Still no luck.
I've downloaded reinstalled looked for missing dependencies and they still will not load up.
I may delete the two sw1500's and start over agin from scratch.
All the sd9's work fine.

Deleted them both, downloaded them again, reinstalled. They still wont load up in surveyor.
These have me confused. I wanted them because they look sort of like Providence Worcestor locos nearby in sturbidge ma.

 

[Euphod]

Ahwright!! Ed

I have about three hours into trying to get these Sw1500' s to load up.
Did you change the kuid #? I'm going to try that out right now let you know how I make out.

Thanks Buddy.

I didn't change anything, just downloaded and it works! Sorry it's not as easy for you...

 

[JCitron]

Now problem downloading here either. There was a missing bogey, but I updated the config.txt to load in the bogey from another locomotive of the same type and that works.

The paint scheme is very similar to Guilford's "crap" paint. The small logo could be replaced with a big G offset towards the cab and it would work perfectly.

http://en.wikipedia.org/wiki/File:EMD_GP40_B&M_339_Wells_Maine.jpg

 

[railroy19]

I give up!

I tried changing bogeys. Deleted all the sw1500s. Downloaded them again several times. Deleted the dependencies reinstalled changed bogeys I don't know what is happening but the engines show up in the drop down asset window but just wont load up in surveyor. They show up as faulty in cmp but have no missing dependencies in the config files. Guess I will have to move on and say uncle.

Thanks anyway guys.
Bob

 

[shaneturner12]

By any chance, did you check what the faults were (right-click, View Errors/View Errors and Warnings)

Shane

 

[railroy19]

Ok Shane

I did this and this is what I found
Error: This asset has a trainz-build number which is not recognised by this tool.

I have no idea what this means.

Thanks so much Shane I looked at the config file and trainz build was 3.4 So I changed it to 2.9 which is in the sd9's config file and sure enough that did the trick.
Oh boy I'm getting so good at this it scares me Look out Bill Gates

Bob

 

[DON49PLM]

Missing a kuid for your sw1500.
The number is 387111:100268
The other engine works fine but the 1500 won't load.
These look like very nice engines and the strobe light is very nice feature.

Thanks for nice content.
Bob

387111:100268 is the strobe light and is a mess in the mess table. I also put it in the kuid table but shouldn't have. if you open it i CCP and remove it from the kuid table it should work fine. I well post a update and fix that. sorry. Wasn't sure about that and now i know:wave:

 

[dnevans8]

I did this and this is what I found
Error: This asset has a trainz-build number which is not recognised by this tool.

I have no idea what this means.

Bob

You probably have not patched to the latest version.

If you open the config.txt file you will see a line beginning with Trainz-build and this will show 3.3 or 3.4. Change this to 3.2 and it should then work.

Or you could patch to the latest version and risk all the problems that arise as others have posted in this forum.

 

[DON49PLM]

You probably have not patched to the latest version.

If you open the config.txt file you will see a line beginning with Trainz-build and this will show 3.3 or 3.4. Change this to 3.2 and it should then work.

Or you could patch to the latest version and risk all the problems that arise as others have posted in this forum.

I just re-posted my SW1500's and I also change the build # to 2.9

 

[railroy19]

Thanks I did just what you just said I changed it to build 2.9 just by luck.
I looked at the config file from your sd9 and copied the build number.
I did remove one kuid that did not look right to me and now I have both sw1500 working fine.

Thanks so much for some fine looking engines.
Bob