GMax and 3DSMax (And any other modeling program) screenies/renders
- Thread starter Mr.Kamikaze
- Start date
socalwb909
Photo Creator
-W.I.P, Trinity 57' spinecars:
-Joe
-Joe
Last edited:
socalwb909
Photo Creator
-I'd say the learning curve is steep but worth climbing the hill. the harder part is trying to find information relating to what tools and everything u need for trs. like one time i tried to look up mapping on youtube and couldn't find hardly anything. come to find out there are so many ways of doing everything!
-Thanks Phil!
-Joe
I try-ed inporting it into Trainz. Due to the material type Google Sketch up uses I was unable to down-convert it in 3dsmax 2008 to export it as a 3ds for Gmax.
Since I do not like Blender for personal reasons I will not even go there. Keep your fingers crossed for a 3dsmax 2011 (64-bit) exporter or maybe someone will create a xml exporter that will allow me to use the developers Trainz conversion tool.
Cheers,
JRT
slave-driver
Sacramento Nothern Lives
EastCoastTrainz
Hating Foamers since 1980
B&O I-18 Class/Chessie C-24 Class. Much work to be done still...
~Zak
~Zak
kittycraft
Member
....
I think I just **** herself.......
I think I just **** herself.......
Last edited:
simulatortrain
jointed freaking rails
YES
We obviously need more cabooses, and I'd enjoy starting with a B&O one!
We obviously need more cabooses, and I'd enjoy starting with a B&O one!
iceman2117
EskreuztkeinWegdenanderen
hi, ...
Not Render.
g'ice
Not Render.
g'ice
Sachsenbahner
Sachsenbahner
Hi iceman, ich finde die Proportion von Bogey und Aufbau wirkt noch etwas unstimmig, ansonsten sieht es vielversprechend aus...
LG Sachsenbahner
LG Sachsenbahner
iceman2117
EskreuztkeinWegdenanderen
Hallo, Sachsenbahner
Der Waggon ist ja noch nicht fertig.
Die Seitenwand muss ja unten zwischen den Tüeren noch nach innen gezogen werden.
Die Seitenwand ist jetzt nur gerade nach unten gezogen, bildet aber die tiefste Stelle.(Waggonmitte)
The carbody is still not finished in Moment.
The side wall has to be pulled down between the doors so still inside.
The side wall is now considered only straight down but is the lowest point. (car center)
g'ice
Last edited:
David111767
30in and Rack Railway Guy
Looks like something you would see in TRON lol
Something from Qld, Australia
Hi Everyone,
Here is the 1899 ancestor of the Auran 1924 Walschaerts PB15; Queensland Railways Steph Valve Gear PB15 and a QR D17 4-6-4T Suburban Tank. So Enjoy.
QR PB15 488; built by Kitson Of Leeds, Works Number 4607 of 1908 and was commisioned on the 3.3 1909 and was written off the 1. 1970. She worked the original Gold Coast Railway until 1965 when it closed to traffic.
QGR D17
:wave:
KIndest Regads
Michael G. & The Team At Queensland Government Railways
Hi Everyone,
Here is the 1899 ancestor of the Auran 1924 Walschaerts PB15; Queensland Railways Steph Valve Gear PB15 and a QR D17 4-6-4T Suburban Tank. So Enjoy.
QR PB15 488; built by Kitson Of Leeds, Works Number 4607 of 1908 and was commisioned on the 3.3 1909 and was written off the 1. 1970. She worked the original Gold Coast Railway until 1965 when it closed to traffic.
QGR D17
:wave:
KIndest Regads
Michael G. & The Team At Queensland Government Railways
Last edited:
Retro00064
New member
Cool! Did you base that PB15 mesh and/or the textures off of the Auran ones? as it sure does look similar. 
Thanks and regards.
Did you base that PB15 mesh and/or the textures off of the Auran ones? as it sure does look similar. Thanks and regards.
Captrain / ITL Eisenbahngesellschaft Baureihe 186 (Bombardier Class 186)
Whoa, very nice, good job on that !:wave: