Recent content by horacefithers

On the BC&SJ route roads have gone underground. Sidewalks and armco barriers are missing. I was thinking of starting work on the route again. Well, it's not going to happen. I don't have the energy to go through the entire route fixing stuff, again (and again). I'm out of here. My Gold...

For all you asset gurus/junkies out there... My particular install of TRS19+ 106618 enters a kind of jerk jerk jerk mode when I Edit Route BCSJ-555-RHR. The jerks occur when moving around in Surveyor with Surveyor lurching from one camera position to the next at about 2 or 3 lurches per second...

I noticed when looking at the dependencies for my BC&SJ route that a number of assets had newer versions available. Many of these were PBR TextureEnv assets. So being foolhardy and adventurous I loaded up the new asset versions, fired up Surveyor, and clicked Edit Route. Not the best idea I'd...

I know how to set the snow line elevation in TRS19 regular version. But I'm in Trainz Plus in the unified cockpit and I'm not seeing a snow line elevation setting (nor cloud type setting!!!) anywhere in either Driver nor Surveyor mode. I started by Edit Session. Do I need to back out and Edit...

I'm not sure, but I think I'm seeing places where the circle at the points of a turnout (made with TRS19 SAP track) is RED instead of white or yellow. I addition to the ever popular lets have the rails at a different height at the frog problem which causes PBR track to fail to form a nice set...

Wow! I got this via email this morning... Trainz Plus 2020 Q1 Update - Official Release The latest update for all our Trainz Plus and Gold Class members is now available on PC and Mac. PC Build 105100 to 106618 (single patch) Mac Build 105113 to 106755 (2 step patch) This update includes...

Are there any EIT gurus out there in forum land? I could use some help with getting trains through Bear Creek yard on the BC&SJ. I would like to run AI trains as background traffic traveling east and west the full length of the railroad spaced about 40 minutes apart so they don't overwhelm...

Hey... I found that two opposing AI trains would usually deadlock at Hampton on my BC&SJ route (I expect there are likely several other places). Hampton has a main and 3 full length sidings (loops). In the test case I set up an eastward train approaches Hampton (from the right). The AI sez...

In 105 miles there are quite a few stations and sidings on the BC&SJ. I've been adding track markers to the east, west, and within these places. _______________B___________________ ______________A__/_________________C_________________\__D________________ Assuming this siding...

I'm testing AI background operation on the BC&SJ route. It's a tedious process. The AI trains are generated at relatively long intervals and it takes 3 hours or so for a train to make it across the 105 mile route. Is there a way to make TRS19 simulate "faster" so that problems in AI...

I was doing some route clean up looking for object assets that had made their way into the session-layer and found this. There's a board square that doesn't have a grid on it in F9 mode. Huh? Photo 1 Photo 2 - same camera angle of same place but F9 mode "off" TRS19 build 105100. Is...

In Trainz Plus driver I found in the hold-ctrl/right button pop up menu (when hover over a locomotive) an item labeled "Drive Schedule". But I've had little luck finding info on schedules in the wiki. What are schedules? How are they created? Enquiring minds need to know! Horace Fithers

I got an AI engineer to move a train! That's the good news. The bad news is, that after pulling out of a siding, then engineer didn't increase speed to track speed. Do I need to put speed limit signs after each siding so the AI engineers will behave better? H. Fithers

I updated (route-wide) a family of JR track with TRS SAP Track U.S. 132LB SG, GB, TP with Spikes, Shiny <kuid:439337:103196> procedural track using the bulk asset replace tool. This time I replaced across the entire route. So far I've found no track kinks. However I noticed that when turnouts...

I used the bulk asset replace tool to change some track from my old standby from JR to TRS19 SAP U.S. procedural track. I used the change within selected area mode. I don't know if this caused the problem but now I'm finding KINKs (not Ray Davies!) where some straightened track segments meet...