.
Results 1 to 7 of 7

Thread: Edging For Different Heights

  1. #1

    Default Edging For Different Heights

    Having another go at a proto-model concept, where I've Transdemed a section of real world railway to enclose in a barn (or aircraft hangar!) size room. However what this does mean is where I prune the edges along the track to represent the scenic area of the baseboard will have the undulating contours of the real world terrain. I was pondering how to adapt our edging sections to this particular situation but at the moment the only solution I can see is to artificially level the edge of the baseboard to an average height over (say) a 500m section and fit the woodwork to that. Where there is a significant difference in adjacent heights I will also probably have to step up the floor to maintain the 70m height of the edging sections. I don't really want to use a backdrop along the edge as the idea is to have the route as a centre walk around table in the model "room".

    Open to further ideas!
    TRS 2019 Coach Class (Former Customer)

  2. #2

    Default

    What I ended up doing was make a custom made asset for those hilly area's. I even ended up hiding a small shadow station inside.

    See here:


    Probably not the best view to see what I mean, so if you want to take a closer look download this M120 "two valley" module from the DLS.

    What I did was make measure the height of the hills along the edge where I needed to make the wall (and shadow station) and used those heights in Blender to create the asset.
    Might be too much work for what you are looking for though. Maybe you could just do with a spline with 10m sections.

  3. #3

    Default

    Yep not quite the solution I was looking for but I will consider it.
    TRS 2019 Coach Class (Former Customer)

  4. #4
    Join Date
    Nov 2006
    Location
    United Kingdom
    Posts
    2,921
    Blog Entries
    2
     

    Default

    If you are using a spline you could try inserting multiple spline points and adjusting their height. It wouldn't smoothly follow the contour but it would possibly look not too bad.
    John,
    (A bear of little brain)

  5. #5

    Default

    That is a good shout John, I'll give that a go.
    TRS 2019 Coach Class (Former Customer)

  6. #6
    Join Date
    Nov 2006
    Location
    United Kingdom, Norfolk
    Posts
    2,578
     

    Default

    Another solution which might suit in some cases would be to have an edging deliberately higher than the baseboard contours (to prevent models falling on the floor!) so that the ground is always lower than the top of the edging. I have done this on an actual model railway, mainly to prevent little fingers from straying.

    Ray
    Dukes Denver Designs (Ray Whiley - Textures and 3d Virtual Models for TRAINZ).
    Member of Trainz Carriage and Wagon Works

  7. #7
    Join Date
    Nov 2006
    Location
    United States of America, Massachusetts, Haverhill
    Posts
    25,582
     

    Default

    Quote Originally Posted by ray_whiley View Post
    Another solution which might suit in some cases would be to have an edging deliberately higher than the baseboard contours (to prevent models falling on the floor!) so that the ground is always lower than the top of the edging. I have done this on an actual model railway, mainly to prevent little fingers from straying.

    Ray
    I remember doing the same. All it was was a piece of card stock that I painted tree blob-texture on and put other trees in front of it. Later on when I got Vistapro I tried printing out 3d landscapes and then I got World Builder and achieved better results, but by then I moved on to TRS2004 and all that became obsolete for me anyway.
    John
    Trainz User Since: 12-2003
    Trainz User ID: 124863
    T:ANE Build: 94829
    TRS2019: 98592

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •