.

Search:

Type: Posts; User: Bill69

Page 1 of 18 1 2 3 4

Search: Search took 0.04 seconds; generated 32 minute(s) ago.

  1. do a search for LMSR signals, they seem to work...

    do a search for LMSR signals, they seem to work ok.

    Bill69
  2. Replies
    3
    Views
    151

    yes, that's what I use too but it should not be...

    yes, that's what I use too but it should not be required. Trainz slow down correctly when approaching a lower speed limit, why can't they when approaching a caution signal?

    Cheers,
    Bill69
  3. Replies
    276
    Views
    33,660

    Sticky: Create a cdp of the asset and save it so you know...

    Create a cdp of the asset and save it so you know where to find it. Then delete the asset from your database, start Trainz then see if the route will load, if it does load do a "delete missing...
  4. Replies
    14
    Views
    368

    When joining track the two spline points must...

    When joining track the two spline points must both be at the same height unless one has not been fixed i.e. one is white instead of yellow. In this case the white one will adopt the height of the...
  5. Replies
    14
    Views
    368

    Yes I think that is a failing in TRS19, spline...

    Yes I think that is a failing in TRS19, spline points don't show in a screenshot and they should show.

    Bill69
  6. Replies
    12
    Views
    213

    It's called the smoke container. In the config...

    It's called the smoke container. In the config file you will see "smoke1, smoke2, smoke3 etc. But if you delete the lot you might come up with an error.

    I have not tried this but it might be...
  7. Replies
    14
    Views
    368

    It is much better to have a short straight after...

    It is much better to have a short straight after the switch i.e the frog side. Also the switch lever should be just on the edge of the spline point on the opposite side to the frog. In the middle...
  8. Replies
    13
    Views
    735

    Frame limiter is in the program. From launch...

    Frame limiter is in the program. From launch screen select "trainz settings" and set vertical sync to half.
    If your refresh rate is 60Hz this will limit your FPS to 30
    Further on this subject,...
  9. Replies
    5
    Views
    248

    Get in touch with RRMods. Bill69

    Get in touch with RRMods.

    Bill69
  10. Replies
    75
    Views
    6,843

    you all could go a bit easier on the op, note he...

    you all could go a bit easier on the op, note he has only 6 posts, obviously a new user. I am sure given a bit of time he will learn how to replace or or find missing objects.

    Cheers,
    Bill69
  11. Replies
    12
    Views
    453

    The way I do it is edit the route. If you see an...

    The way I do it is edit the route. If you see an orange box place a similar item you want next to it then do a "delete missing objects" save and close the route.
    Re open the route then move the...
  12. Replies
    6
    Views
    167

    Hi lenscab, There are two reliable ways to set...

    Hi lenscab,

    There are two reliable ways to set up a session. Fist load the route and select "create session" You can select the command library in the driver commands panel. You can then program...
  13. Replies
    1,191
    Views
    178,335

    Hi, I have kuid2:334896:38013:1 missing from...

    Hi,

    I have kuid2:334896:38013:1 missing from mohaka viaduct by Vulcan. Can anyone help with this one?

    Cheers,
    Bill69
  14. In addition to what others have said you need to...

    In addition to what others have said you need to level the ground all round and under the turntable and the roundhouse. Do this before you place the turntable and the stubs will connect with out...
  15. Have you tried replacing the item you edit before...

    Have you tried replacing the item you edit before running it? I know it is required with locos if you change the e-spec in any way.

    Cheers,
    Bill69
  16. Replies
    5
    Views
    150

    As far as I know you can't, decouple before...

    As far as I know you can't, decouple before loading the tender then couple to the consist after loading.

    Cheers,
    Bill69
  17. Replies
    5
    Views
    150

    You should tell him to drive to the tipple, ...

    You should tell him to drive to the tipple, load, then drive on to next destination
    If the tender does not load it could be because there is no load queue in the config file or because the tender...
  18. Replies
    47
    Views
    4,088

    I still have all the steam engine sounds, don't...

    I still have all the steam engine sounds, don't know about the rain never use it, as for air brakes I never use diesel electrics either.

    Cheers,
    Bill69

    Just tried it on my test track, I still...
  19. Replies
    47
    Views
    4,088

    I tried to replace the sounds with Dave's silent...

    I tried to replace the sounds with Dave's silent sounds but still could not commit the sounds, so I found an easier way.
    Open CM and find the sound kuid 570470 100003 click on it and go to "content"...
  20. Thread: SILVERFREE

    by Bill69
    Replies
    10
    Views
    344

    Was it posted on the first of April?

    Was it posted on the first of April?
  21. Thread: Authorization

    by Bill69
    Replies
    30
    Views
    711

    So where does this come from? ...

    So where does this come from?

    boiler-efficency
    boiler-efficency-idle
    boiler-efficency-min
  22. Replies
    12
    Views
    543

    Ah! You are right, the electrics were removed...

    Ah! You are right, the electrics were removed about eight or nine years ago.

    Cheers,
    Bill69
  23. Replies
    12
    Views
    543

    That is exactly what grade is in the Otira Tunnel...

    That is exactly what grade is in the Otira Tunnel and it's 8.5 kilometers long. So if you are doing a prototypical route of the west Coast that is what you should be using. Steam locos are not...
  24. Replies
    2
    Views
    236

    What is the kuid number of the station you are...

    What is the kuid number of the station you are using? I have read that the stations with a suffix of :22 do not work as intended, for that reason I have stuck to an earlier version with a suffix of...
  25. Replies
    7
    Views
    429

    Yes it is quite possible to re-tune the smoke on...

    Yes it is quite possible to re-tune the smoke on each loco if you use the smoke container in the config file, time consuming but possible, but a bit more complicated if you use a TFX file for the...
Results 1 to 25 of 435
Page 1 of 18 1 2 3 4