.

Search:

Type: Posts; User: Kennilworth

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Hi You need a base session with all the...

    Hi

    You need a base session with all the schedules entered, checked and working properly. For future sessions open the base session in Surveyor and immediately use Save As to save it as a session...
  2. Replies
    7
    Views
    216

    Hi A bit of information about Un-portals for...

    Hi

    A bit of information about Un-portals for those who are unfamiliar with them.

    Un-portals can produce a maximum of 99 consists. This figure is divided by the number of Un-portals on a route...
  3. Replies
    8
    Views
    269

    Hi David I've noticed on more than one...

    Hi David

    I've noticed on more than one occasion that in sessions brought in from TANE the driver commands often don't work correctly, if at all. Removing them and re-entering them will cure the...
  4. Hi I'm only aware of one signal related...

    Hi

    I'm only aware of one signal related autodrive command which is "AutoDrivePastSignal" by author "pguy" and is on the DLS. It is unlikely to be of use to you because it is extremely difficult to...
  5. Replies
    15
    Views
    596

    Hi These are used to indicate if a track...

    Hi

    These are used to indicate if a track section is occupied or not and are used in conjunction with Mission Codes to enable a consist to find a vacant track.

    At a terminus station for example...
  6. Hi It's been a long time since I ran Marias...

    Hi

    It's been a long time since I ran Marias Pass but if I remember correctly they used Un-portals to produce consists when required by using triggers to determine when they should be produced.
    ...
  7. Thread: Priority?

    by Kennilworth
    Replies
    4
    Views
    231

    Hi Dick The only way that I can see of doing...

    Hi Dick

    The only way that I can see of doing this is to use a variable that the faster train can set to indicate that it is approaching the section. Before a slower train can enter the section it...
  8. Replies
    18
    Views
    635

    Hi EJB If Coal Loader 40 isn't loading all of...

    Hi EJB

    If Coal Loader 40 isn't loading all of the wagons it suggests that it isn't producing enough coal to fill the full train. Have you tried increasing the amount of coal produced every 30...
  9. Hi Dick In my experience an industry will...

    Hi Dick

    In my experience an industry will continue to fill the cars until it runs out of product. It then loads full or partially intermittently until the whole train has passed through. I can't...
  10. Hi Bob This is just what I've been looking...

    Hi Bob



    This is just what I've been looking for. Most coal loaders load at much too high a speed to be realistic so I'll be changing the existing ones for yours now. I think it looks ridiculous...
  11. Replies
    9
    Views
    504

    Hi Ken It looks from your screenshot as if it...

    Hi Ken

    It looks from your screenshot as if it may be an AWS TRIGGER.

    Regards

    Brian
  12. Replies
    1
    Views
    286

    Hi A lot of JR freeware has appeared on the...

    Hi

    A lot of JR freeware has appeared on the DLS over the last couple of days so it may yet turn up there.

    Regards

    Brian
  13. Replies
    4
    Views
    302

    Hi Leo I don't know what is happening with...

    Hi Leo

    I don't know what is happening with your installation but I rarely use portals to consume consists unless I need the consist to return later. At all other times I place a trackmark at a...
  14. Replies
    13
    Views
    695

    Hi Yes this will work. Out of interest I...

    Hi

    Yes this will work. Out of interest I tried it at the weekend when I upgraded my TRS19 install to a 1Tb from a 500Gb one. As I had no free Sata connectors in the computer I had to use an...
  15. Hi Leo I've just discovered that platform 2 is...

    Hi Leo

    I've just discovered that platform 2 is the single track bay on the left platform looking North. Like yourself I couldn't get past signal 5C62 so I investigated further. Hovering the mouse...
  16. Replies
    73
    Views
    3,166

    Hi I bought TRS19 as soon as it was released...

    Hi

    I bought TRS19 as soon as it was released and have never looked back. As far as lighting goes it takes a little bit of experimenting to get it correct for what each individual thinks is right...
  17. Replies
    7
    Views
    292

    Hi Dick I've had no issues using JR signals...

    Hi Dick

    I've had no issues using JR signals with Enhanced Interlocking Towers. When setting a path up in an EIT I make sure that the first signal is set to Automatic and not left on the default of...
  18. Replies
    3
    Views
    161

    Hi If this is occurring in TANE then check if...

    Hi

    If this is occurring in TANE then check if you are getting a timeout error. I have a lot of commodities installed and have had a similar issue to yourself.

    My solution was to list the...
  19. Hi Dave I remember it well and really miss it....

    Hi Dave

    I remember it well and really miss it. It was a great system which was written by Mike Carter and was streets ahead of anything else. Like yourself I was able to produce long automated...
  20. Replies
    13
    Views
    1,014

    Hi Have a look at this thread ...

    Hi

    Have a look at this thread

    https://forums.auran.com/trainz/showthread.php?143793-Driver-commands-to-support-uncoupled-rear-assistance-of-train-up-steep-grades&highlight=elstoko

    Regards
    ...
  21. Replies
    15
    Views
    1,599

    Hi A clean install of TRS19 only contains the...

    Hi

    A clean install of TRS19 only contains the Content Samples and Kickstarter County routes. However as has been pointed out if you don't install the others you will be missing a lot of content.
    ...
  22. Replies
    9
    Views
    618

    Hi again You will need to use andi06's...

    Hi again

    You will need to use andi06's junctions instead of the ones by Mike10. They will work with any point motors.

    Regards

    Brian
  23. Replies
    9
    Views
    618

    Hi Craig72 If recall correctly I think that...

    Hi Craig72

    If recall correctly I think that those junctions exploited a bug in TRS004 to enable them to work. The bug was fixed in later versions rendering the junctions as faulty.

    Try using...
  24. Thread: Disk Space

    by Kennilworth
    Replies
    11
    Views
    502

    Hi Just for information - I've just installed...

    Hi

    Just for information - I've just installed TRS19 on a 250Gb SSD and a clean install before any DLC or DLS assets have been downloaded shows as about 17Gb. The userdata folder is also on this...
  25. Replies
    17
    Views
    926

    Hi If you use rmm speed trees he has v5...

    Hi

    If you use rmm speed trees he has v5 speedtrees that automatically update to v6 in Tane and TRS19. You only need to update them once in TS12 instead of updating again in Tane or TRS19.
    ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4