.

Search:

Type: Posts; User: mtldrm38

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    9
    Views
    360

    Yep I use that site often the issue was the...

    Yep I use that site often the issue was the aerial view s most of the track are in the shade...(1955-63) but I am measuring the area with google earth and tracing the trackage with the topo's......
  2. Replies
    9
    Views
    360

    pretty neat site will come in handy... Thnx Dave

    pretty neat site will come in handy...
    Thnx Dave
  3. Replies
    9
    Views
    360

    Oh wasnt aware this route., have to take a look...

    Oh wasnt aware this route., have to take a look at it...
    Just found it for TS19 nice little route baesd on model railroader magazine...
    Thanx Dave =)
  4. Replies
    9
    Views
    360

    thanks John found these earlier not much data as...

    thanks John found these earlier not much data as far as trackage since the line has been torn up since the 70 s ugh....
    I been scouting a lot of photos gonna try piece meal it from theyre …
    Dave =)
  5. Replies
    9
    Views
    360

    Looking for switching map:milw beer line

    Looking for track diagram switching maps for milwuakee ,wis.
    Mainly the BEER LINE..
    GOOGLE is useless and NETR maps are pretty much blurry hard see whats what...

    Thanx Dave =)
  6. Replies
    3
    Views
    248

    Are you refering to the pop up window that use to...

    Are you refering to the pop up window that use to ask which path you want to select?
    rule: interlocking tower path selection rule ui...just check the box that says show paths....
  7. Replies
    4
    Views
    328

    I use the EIT TRC3 INVISIBLE (SHOULD BE AT LEAST...

    I use the EIT TRC3 INVISIBLE (SHOULD BE AT LEAST THE ENHANCED INTERLOCKING TOWER)I only use the tower manager and mission code manager...
    rules ITSETPATH and REMOVE ITSETPATH and ADD MISSION CODE...
  8. This is one of the reasons I decided to work with...

    This is one of the reasons I decided to work with the EIT towers every other set up keep having issues...
    Yet though EIT s will become A strain when as in my case with a couple of routes require...
  9. Replies
    4
    Views
    424

    In surveyor you can place a engine facing the...

    In surveyor you can place a engine facing the signal and it will show its status as in run mode., that's how I test signals are proper when in run mode...
    Dave
  10. Replies
    21
    Views
    1,122

    Happened to me also then crashed., upon re...

    Happened to me also then crashed., upon re starting had the save option and I declined to save changes and it brought me back to original view....

    Dave =)
  11. Replies
    11
    Views
    988

    yes the TEH use to have c628 s I don't think he...

    yes the TEH use to have c628 s I don't think he got around to adding them yet to his new site...
  12. Thread: Steel Mill

    by mtldrm38
    Replies
    15
    Views
    1,242

    To bad this guy never got to release that route...

    To bad this guy never got to release that route...
  13. Thread: Steel Mill

    by mtldrm38
    Replies
    15
    Views
    1,242

    Theyre is a old route by Phileskene called...

    Theyre is a old route by Phileskene called Industrialrail it includes a large steel mill complex laid out that may help you with ideas....
    Dave =)
  14. Thanks Pierre...I believe I solved the issue I...

    Thanks Pierre...I believe I solved the issue I switched towers to TRC invisible and reset config to STATIC MODE (previously using the CROM TOWERS)I have just been running for over a hour and the...
  15. Replies
    15
    Views
    913

    The DECOUPLE COMMAND I found doesnt work well and...

    The DECOUPLE COMMAND I found doesnt work well and my solution was as I forgot to state to manually uncouple the apply the COUPLE COMMAND...
    Sorry for the misguided advice...
    Dave =)
  16. Drivers switching trains and mission code assignments?

    scenario in examples...
    1.driver is sean assigned a passenger train with specific mission code routing., basically point A to B then REPEAT command...
    2.driver is david assigned a freight train...
  17. Replies
    15
    Views
    913

    I just use couple to: now and it works 100% for...

    I just use couple to: now and it works 100% for me...runaround train was always hit and miss...
    Dave =)
  18. try your search again on the dls as CNW... Dave

    try your search again on the dls as CNW...
    Dave
  19. Ya I noticed that and also knew they were gonna...

    Ya I noticed that and also knew they were gonna do such but for me., I downloaded a few assets and half showed up faulty...
    I am just trying to get a few routes finally completed...
    I am sure...
  20. Basically I had 3 routes I put into TS19 from...

    Basically I had 3 routes I put into TS19 from Tane and low and behold assets started becoming unavailable as I was trying to transform them...
    So I deleted them and switched back to TANE...
  21. I remember that headache but majekear released a...

    I remember that headache but majekear released a lot of his boxcars with build3.7., built ins ugh... only thing you can do is a bug report and hopefully tume re does those boxes?
  22. Replies
    8
    Views
    755

    Thanks John will look those trees up and yes half...

    Thanks John will look those trees up and yes half the PBR are way out of scale but theyre have been a lot of newly uploaded ones on DLS I been finding that look pretty good...
    Dave =)
  23. Replies
    8
    Views
    755

    I agree its good with new and small routes but...

    I agree its good with new and small routes but large I just went back to grass splines and all PBR textures overall things are really working well otherwise...wondering also what speed trees anyone...
  24. Yes thank you for the link also., and trainboi1...

    Yes thank you for the link also., and trainboi1 did a great job with this track... I did a bulk asset replace on a large route only issue was had to double click straighten tool at the points but...
  25. Replies
    6
    Views
    377

    Oddly enough it seems a lot of JR stuff is...

    Oddly enough it seems a lot of JR stuff is showing faulty, etc...
    I went back to JR website redownloaded files from theyre and installed them most worked so far...
    Dave =)
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4