.

Search:

Type: Posts; User: stagecoach

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Yes, all assets of the package will be deleted...

    Yes, all assets of the package will be deleted unless some of them are on the DLS or in another DLC package you are using.
  2. Because the session is linked to the route, it...

    Because the session is linked to the route, it needs the actual route worked on. When it says save route and session just select ok. This saves both route and session under your kuid. Work on the...
  3. Replies
    5
    Views
    147

    There is a Sen City switcher...

    There is a Sen City switcher <kuid2:76656:500000:1> Sen City Road Switcher which could do the trick.
  4. Removed Post

    Removed Post
  5. The DLS thumbnail is a general view of the asset,...

    The DLS thumbnail is a general view of the asset, and may include identifying text or logos. This must always be 240 x 180 pixels, and must be in jpeg (jpg) format. All assets must have the default...
  6. As well as the map-kuid did you change the kuid...

    As well as the map-kuid did you change the kuid table?
  7. Replies
    12
    Views
    205

    Have you tried revert to original?

    Have you tried revert to original?
  8. Have you entered your username and password in...

    Have you entered your username and password in the settings section of the launcher screen?
  9. Glad you got it sorted, I use the message...

    Glad you got it sorted, I use the message commands because only the train that sends it triggers the other engine. The message will sit waiting until a train that wants that message picks it up....
  10. It was done with TANE as I don't have the older...

    It was done with TANE as I don't have the older versions installed. Don't have an answer to the engine not moving as I have never encountered that problem.
  11. Replies
    10
    Views
    253

    These may have been updated in another DLC...

    These may have been updated in another DLC package that you do not have installed. I know that if you list asset versions the LMS Coronation Scott shows an update in a different DLC package. This...
  12. The demo I sent you will allow the helper engine...

    The demo I sent you will allow the helper engine to do its task over and over again each time it gets that message. Only a train that sends the message will activate the helper while other trains...
  13. Sample sent. The only command that I know that...

    Sample sent. The only command that I know that keeps the instructions is "move to train at TM". It carries all the driver commands with him so he can move from train to train as many times as you...
  14. It needs a few small extra assets placed to work...

    It needs a few small extra assets placed to work but it can be done fully automated with AI. I have a small demo route of how to split a train that shows how to use two drivers with the same consist...
  15. Only one driver can be in a consist at any one...

    Only one driver can be in a consist at any one time. You need to move the passenger driver out of the train while the helper engine is coupled up. Once the helper engine uncouples you can put the...
  16. Replies
    3
    Views
    129

    Open the edit-config of the session and look for...

    Open the edit-config of the session and look for map-kuid. Check to see the kuid of the route it was attached to. If different from the route you are using try and change the kuid to match your...
  17. Replies
    8
    Views
    211

    You just go into driver mode for them to work.

    You just go into driver mode for them to work.
  18. Replies
    8
    Views
    211

    How have you selected the green and red correctly...

    How have you selected the green and red correctly in the controller setup?
    Route 1 = G, R, R.
    Route 2 = R, G, R.
    Route 3 = R, R, G.
    If this is in surveyor then they don't work, the same as all...
  19. In the layers tab, all layers in the top section...

    In the layers tab, all layers in the top section will save to the route. All layers in the bottom section will save to the session. You need to select edit session to get the saved session layers...
  20. Replies
    7
    Views
    278

    There are larger stoppers on the DLS available...

    There are larger stoppers on the DLS available for wider crossings thus avoiding the two stoppers.
  21. Replies
    1
    Views
    104

    Go to My Trainz and download TRS19 again and you...

    Go to My Trainz and download TRS19 again and you will have the latest public version. You can always copy the old data to the new one.
  22. See this post. ...

    See this post.

    https://forums.auran.com/trainz/showthread.php?164711-Wisdom-of-the-Ancients-on-traffic-vehicles
  23. Did you close the properties window of the TM...

    Did you close the properties window of the TM before you did the undo? The crash was most likely Trainz looking for the TM that the property's window belonged to.
  24. Your timeline shows you have Platinum.

    Your timeline shows you have Platinum.
  25. "Couple at trackmark" does not need to know the...

    "Couple at trackmark" does not need to know the wagon number, it just couples to the first wagon nearest the TM.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4