Search:

Use the 09 version. The earlier ones don't have a suitable sound file.

Cheers,
Bill69

Hi hert,
As John said in his first post that did work ok in earlier versions. I have used it in a few routes that I did not have the correct track for.

The Bulk Asset replace saved me a lot of...

I fully understand Horace. I am almost at the same point, getting totally brassed off fixing things instead of running Trainz. Why would any company allow "texture" files in one version then make...

do a search for LMSR signals, they seem to work ok.

Bill69

yes, that's what I use too but it should not be required. Trainz slow down correctly when approaching a lower speed limit, why can't they when approaching a caution signal?

Cheers,
Bill69

Create a cdp of the asset and save it so you know where to find it. Then delete the asset from your database, start Trainz then see if the route will load, if it does load do a "delete missing...

When joining track the two spline points must both be at the same height unless one has not been fixed i.e. one is white instead of yellow. In this case the white one will adopt the height of the...

Yes I think that is a failing in TRS19, spline points don't show in a screenshot and they should show.

Bill69

It's called the smoke container. In the config file you will see "smoke1, smoke2, smoke3 etc. But if you delete the lot you might come up with an error.

I have not tried this but it might be...

It is much better to have a short straight after the switch i.e the frog side. Also the switch lever should be just on the edge of the spline point on the opposite side to the frog. In the middle...

Frame limiter is in the program. From launch screen select "trainz settings" and set vertical sync to half.
If your refresh rate is 60Hz this will limit your FPS to 30
Further on this subject,...

Get in touch with RRMods.

Bill69

you all could go a bit easier on the op, note he has only 6 posts, obviously a new user. I am sure given a bit of time he will learn how to replace or or find missing objects.

Cheers,
Bill69

The way I do it is edit the route. If you see an orange box place a similar item you want next to it then do a "delete missing objects" save and close the route.
Re open the route then move the...

Hi lenscab,

There are two reliable ways to set up a session. Fist load the route and select "create session" You can select the command library in the driver commands panel. You can then program...

Hi,

I have kuid2:334896:38013:1 missing from mohaka viaduct by Vulcan. Can anyone help with this one?

Cheers,
Bill69

In addition to what others have said you need to level the ground all round and under the turntable and the roundhouse. Do this before you place the turntable and the stubs will connect with out...

Have you tried replacing the item you edit before running it? I know it is required with locos if you change the e-spec in any way.

Cheers,
Bill69

As far as I know you can't, decouple before loading the tender then couple to the consist after loading.

Cheers,
Bill69

You should tell him to drive to the tipple, load, then drive on to next destination
If the tender does not load it could be because there is no load queue in the config file or because the tender...

I still have all the steam engine sounds, don't know about the rain never use it, as for air brakes I never use diesel electrics either.

Cheers,
Bill69

Just tried it on my test track, I still...

I tried to replace the sounds with Dave's silent sounds but still could not commit the sounds, so I found an easier way.
Open CM and find the sound kuid 570470 100003 click on it and go to "content"...

Was it posted on the first of April?

So where does this come from?

boiler-efficency
boiler-efficency-idle
boiler-efficency-min

Ah! You are right, the electrics were removed about eight or nine years ago.

Cheers,
Bill69