.

Search:

Type: Posts; User: Kennilworth

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Hi Matt Is this for a player train or an AI...

    Hi Matt

    Is this for a player train or an AI train? Which IT are you using, the Auran one or the P Guy one?

    I've never used the monorail assets but if they work in the same way as normal track...
  2. Hi Pierre advises to keep the number of track...

    Hi

    Pierre advises to keep the number of track objects in a tower (signals and junctions) below 450. The number of paths will depend on how many objects each path contains. I have had up to 45...
  3. Hi Mark I would set up a MC named Penz to be...

    Hi Mark

    I would set up a MC named Penz to be used for the bulk of the route with a change to one of four MCs a couple of miles outside the station - Penz P1, Penz P2 etc - depending which platform...
  4. Hi As far as I know there is no way that an...

    Hi

    As far as I know there is no way that an EIT will allow two trains into a section controlled by a TCB but I'm sure Pierre will correct me if that is incorrect.

    The only way that I've been...
  5. Replies
    4
    Views
    374

    Hi Dick The Crowecombe tower is the original...

    Hi Dick

    The Crowecombe tower is the original one supplied by N3V.

    For Mission Code use you need to use the Enhanced Interlocking Tower (EIT) created by 'pguy'. This one has many enhancements...
  6. Replies
    5
    Views
    151

    Hi It may be the script. The Instant Load...

    Hi

    It may be the script. The Instant Load command for instance states that it will not load locos or tenders.

    Regards

    Brian
  7. Replies
    10
    Views
    275

    Hi Add the 'Schedule Library' rule (built in)...

    Hi

    Add the 'Schedule Library' rule (built in) to the session and create your schedules in that. You can then copy the required schedule into any loco schedule by using the driver command 'Copy...
  8. Hi Horace Removing the signals would render...

    Hi Horace

    Removing the signals would render the EITs inoperable. Paths have to start and finish at a signal.

    Regards

    Brian
  9. Hi Try moving the trigger a bit further from...

    Hi

    Try moving the trigger a bit further from the crossing. Apparently the crossing is opened when the train gets the same distance past it as the trigger is from the crossing. Only use one trigger...
  10. Replies
    9
    Views
    508

    Hi This may help ...

    Hi

    This may help

    https://sites.google.com/site/trcv2english/0-introduction

    Regards

    Brian
  11. Replies
    20
    Views
    889

    Hi One of the problems that the AI has is that...

    Hi

    One of the problems that the AI has is that people want to use it in the way that they think it should work. Unfortunately most of them have different expectations of how it should work and end...
  12. Hi Horace My first thing that I would try...

    Hi Horace

    My first thing that I would try would be to make arrival/dep track 1 the path for Westbound trains and arrival/dep track 2 the path for Eastbound trains (or vice versa). That should...
  13. Replies
    11
    Views
    345

    Hi Another possibility is a Win 10 issue. When...

    Hi

    Another possibility is a Win 10 issue. When MSGSapper created his loading tracks a few months ago I couldn't get a consist to Navigate to them while no one else seemed to have a problem. I...
  14. Replies
    2
    Views
    202

    Hi I believe that the trigger only detects the...

    Hi

    I believe that the trigger only detects the approach of the train and the release is coded in the script and can't be adjusted. Your problem is probably due to the slow speed of the loco over...
  15. Replies
    8
    Views
    281

    Hi Frogpipe is correct. I had a similar...

    Hi

    Frogpipe is correct. I had a similar problem and after a bit of trial and error found that it was a faulty item of rolling stock causing the problem. Unfortunately I can't remember which one it...
  16. Replies
    17
    Views
    1,036

    Hi If you want unpredictability in a session...

    Hi

    If you want unpredictability in a session then variables are the way to go. I almost always use driver commands to set variables on the fly as they can be used to make decisions on which part...
  17. Hi Horace One thing to remember with the...

    Hi Horace

    One thing to remember with the Schedule Library is to NOT use the Repeat command on any schedule that copies commands from the Schedule Library. It not only copies the Copy command but...
  18. Replies
    9
    Views
    334

    Hi Here's a link to the authors website and...

    Hi

    Here's a link to the authors website and instructions on how to set it up.

    https://sites.google.com/site/trcv2english/0-introduction

    The only things that come to mind are:

    Are you...
  19. Replies
    2
    Views
    203

    Hi I've been adding some of these to a route...

    Hi

    I've been adding some of these to a route over the weekend in TS19 Platinum and they are working just fine. Check that you have the latest versions of everything installed as there were updates...
  20. Replies
    4
    Views
    625

    I have had problems with this asset in the past...

    I have had problems with this asset in the past in Tane. My issue turned out to be the sheer number of commodities installed which was causing a timeout error in the scripting when building the list...
  21. Replies
    7
    Views
    586

    Hi Good to know that these are available...

    Hi

    Good to know that these are available again. Have they been updated to work correctly in Tane? I bought them about 10 years ago and moved them into TS12, Tane and TRS19 but there were issues...
  22. Replies
    7
    Views
    586

    Hi Eldavos website closed more than 5 years...

    Hi

    Eldavos website closed more than 5 years ago and as far as I know he no longer has any interest in trainz. I've no idea how you would contact him now but it would be interesting to hear where...
  23. Replies
    8
    Views
    490

    Hi Just drive the train via a trackmark and...

    Hi

    Just drive the train via a trackmark and follow immediately with a Delete Train command to get round the portal problem.

    Regards

    Brian
  24. Replies
    11
    Views
    322

    Hi Not sure why you need 2 triggers on a...

    Hi

    Not sure why you need 2 triggers on a track. The trigger allows you to set a distance in front of it and behind it for activating the crossing. I've only ever used one trigger per track as...
  25. Hi Dick Have a look at this Wiki page...

    Hi Dick

    Have a look at this Wiki page http://online.ts2009.com/mediaWiki/index.php/Enhanced_Interlocking_Tower

    Near the bottom it shows you how to edit the config file of any asset to add...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4