Search:

After watching, and checking signal status, almost all instances of "false Red signals" were due to a following switch not properly by the time a train arrived the target signal. The amount of time...

The process provided by TypeForm should extend the list parallel to the first if it cannot be retained on one page. That way the customer can see ALL of the options including the Other. Anyhow,...

Successfully reported "bug" - red signal". I forgot to note that the train does resume its travel after 10 seconds to about a minute.

The list of build numbers did not contain my number. I...

I went directly to Bug Report from the Test Case page (http://www.trainzportal.com/pages/beta-test-center). After looking at the Test Case stuff I went to Bug Report. Same issue there as before - my...

Does not work.It is a "Bug Report" page. It asks for the build number but when I begin entering a suggested list appears and it goes no higher than 104426. Typing my 104480 and it simply re-asks the...

My reports kick back saying I should use the official Beta Problem Reporting Process. I looked through the known reporting stuff and searched but I can't find an official Beta reporting thread.Wasted...

One problem is that I have had several CTDs while investigating my signaling issues. They occur at random times and at random points in the route, or a loading process. There is no pattern. Right now...

I fiddled with the Pause as the train approached a "delaying" red. No change. Turned the engine around to backwards, no change, return to forward, no change.

Tried again and it worked. Continued...

I have had red signals appearing with no apparent cause. "Mouse Over" said that a switch was no properly aligned. Clicking on the red signal took me to the mis-aligned switch. Eventually after up-to...

In the Beta I saw little if any positive sharpening of an already sharp image. However, when I tried the sharpening at maximum settings the image showed evidence of noise on the edges of the PBR...

Is there a track (or track series) that is compatible with PB?. That is, a track that will not be effected by adjacent PBR textures resulting in different amounts of track disappearing, or at least...

I used the Beta in the hope that some issues were fixed. I agree it was a stupid move, as was my removing the working version ( crowded SS). However, I had a problem and reported it in good faith. I...

Finally gave up and reverted to a CDP I had saved. It was only a few days old so not much lost. Just the usual missing textures otherwise appears to be intact. Running a session that looks good. Who...

While editing a PBR asphalt(2) texture the program disappeared.
Restarted and reloaded the route. It was now a blank single base-board.
Just wanted to note that there remains problems of various...

FIXED -- Clear all options in Driver Setup....

Many thanks for the rapid response.:)

Recently there was a post by Tony Hilliam that listed a cross reference of SCxxxx IDs to actual product names. I failed to save:'( that message. Does anyone have a copy of the cross-reference?

Report on erasure of commands to second train:

I failed to mention that I am using the TIMECHECK rule:

Also, if I start 2 trains at 10:00, both using time-check, the second train specified in...

Another problem: at 10:00 train1 drives toward a tipple. At 10:01 all of the commands for Train 1 disappear. At 10:01 a second train was started. Altering the start time of the second train also...

Train not stopping at station:

On the Hinton route, and a single clean baseboard route, the train does not stop at the station/depot. I have tried several stations/depots but always the same....

Yep, that worked. I never paid close attention to the size of the brush and did not realize why it worked well sometimes. Thanks!

I had not seriously considered the PBR "stuff" until I had tried it on a route. I am impressed and intend to adopt/replace. However, I can't avoid the visual impact (dropout) of PBR textures adjacent...

Thanks, problem is with the RED light switch. Again thanks....

104480 I continue to see where the train stops at a red signal, with no obvious reason for red. Clicking on the red signal shows a message the signal nnnnn id "not properly aligned". Double...

You may be on to something. Clicking on a "false" red signal took me to a JUNCTION not near, but was pulsating/blinking. I could see nothing wrong but redid the signal and removed all PBR textures...