.

Search:

Type: Posts; User: davidbird

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Thanks Pierre, looking forward to the update.

    Thanks Pierre, looking forward to the update.
  2. Apologies, I've obviously not been clear enough. ...

    Apologies, I've obviously not been clear enough. I should have said "when a path, allocated to a train, is cancelled without the train completing the path"

    Does this help?
  3. Enhanced Interlocking Tower paths not resetting

    I'm using pguy's TRC Enhanced Interlocking Tower and associated driver commands. All are the latest versions. I'm also using the built-in IT SetPath and IT Cancel Path rules.
    This is in the latest...
  4. Replies
    8
    Views
    275

    Confirmed as a bug by N3V, in for fixing in next...

    Confirmed as a bug by N3V, in for fixing in next update.
    Thanks for all your help.
  5. Replies
    8
    Views
    275

    Update It is not a problem on transferring from...

    Update
    It is not a problem on transferring from TANE to TRS2019. The recently added VM rule is now doubled! Also the Show Variables rules are also doubled!


    Thanks Trevor, but that doesn't...
  6. Replies
    8
    Views
    275

    Thanks Brian, As far as I can tell, the driver...

    Thanks Brian,
    As far as I can tell, the driver commands are working as expected. Deleting the Variable Modify rule and re-entering it just brings the problem back.

    Of course, I can completely...
  7. Replies
    8
    Views
    275

    I tried deleting the Input Table rule - all runs...

    I tried deleting the Input Table rule - all runs properly - but the Input Table is necessary to setup the driver commands to use the variables, so I've re-instated it.

    Don't think this can be the...
  8. Replies
    8
    Views
    275

    Update I added another top-level instance of...

    Update

    I added another top-level instance of the Variable Modify rule , which worked just as expected.

    So I deleted the original VM rules, but when the session was ran again, the values were...
  9. Thread: Brake Test

    by davidbird
    Replies
    5
    Views
    210

    Thanks to all who replied. I think I will have...

    Thanks to all who replied. I think I will have to stick with using HTML messages to simulate the shunter asking for the brake to be made, then giving the OK. Is there a rule to check if brake is...
  10. Replies
    8
    Views
    275

    Variable setup - possible bug

    I'm running build 103369. I have a session where I have set up a shunt in a power station and used session variables to control it

    I have used the Input Table rule kuid2:131986:1012:1 to define...
  11. Thread: Brake Test

    by davidbird
    Replies
    5
    Views
    210

    Brake Test

    Ever since the introduction of the Automatic Brake on British trains, it has been mandatory to perform a "brake test", after formation of the train is complete but before setting off, to ensure the...
  12. Replies
    16
    Views
    1,388

    It's my experience that if an asset needs...

    It's my experience that if an asset needs programming by the user to act in a certain way, then, although the asset itself will save in the route layer, the programming will not. A way round this is...
  13. Replies
    9
    Views
    347

    Hi Dick MCM does allow timed departures as you...

    Hi Dick
    MCM does allow timed departures as you need. All it does is allocate paths to a train.
    By using DriverCommands Active autopilot/Stop at trackmark - Wait until time - Autopilot to trackmark...
  14. Replies
    4
    Views
    266

    I have also had this happen in TRS2019. I was...

    I have also had this happen in TRS2019. I was unaware of any problem on saving, but when re-opened the route, there was just one baseboard.

    You have kept a back-up, haven't you?
  15. Replies
    26
    Views
    1,627

    Yes I had tried but it didn't work, hence the...

    Yes I had tried but it didn't work, hence the question. Given your assurance that it should, I've tried again and I think it was my mistake in forgetting the "set" and "clear" delay times for the...
  16. Replies
    26
    Views
    1,627

    I have this problem, and can't see what to do...

    I have this problem, and can't see what to do about it. I was using the ATLS system quite successfully to control level crossings and their protecting signals. Doing this by using the inverse slave...
  17. Replies
    64
    Views
    5,378

    I am still slowly plugging away at my...

    I am still slowly plugging away at my Nottingham/Trent route, which when (if...) completed will be almost the area covered by Trent PSB, less a few bits plus a few different bits. At the moment the...
  18. No it isn't ! Just found out about it yesterday,...

    No it isn't ! Just found out about it yesterday, only way out was paste a blank area over, or revert to an earlier backup.
  19. Replies
    33
    Views
    2,865

    Not just back in the 80s. The spectacular images...

    Not just back in the 80s. The spectacular images from the Hubble Telescope are all constructed with artificially coloured images, see here http://www.astronomymark.com/hubble_palette.htm
    673nm...
  20. How to change delay on ATLS UK MCG gates?

    I am using the ATLS UK MCG LH 5m and ATLS UK MCG RH 5m <kuid:190624:600051:3> and <kuid:190624:600061:3> gates on a custom crossing.

    It all works as expected, except for the delay on opening the...
  21. Replies
    4
    Views
    358

    TransDEM would do this in TS12 and TANE. You can...

    TransDEM would do this in TS12 and TANE. You can simply tell it to raise a whole route by a set amount. It's payware (but very good value if you're making a prototypical route, with excellent...
  22. Sounds very interesting and useful. You've got...

    Sounds very interesting and useful. You've got my vote to carry on with this!
  23. Replies
    17,910
    Views
    4,685,097

    Hi Scott. Is the viaduct one of yours? I've...

    Hi Scott. Is the viaduct one of yours? I've been looking for something like this for a while, is it (or will it be) available on the DLS?

    Cheers
    David
  24. Replies
    37
    Views
    2,999

    Remember, in UK practice at least, multiple track...

    Remember, in UK practice at least, multiple track spacing is not even. A pair of tracks have a "6-foot" between them, which is more or less a track spacing of 3.5m in Trainz. Any other track (or...
  25. Replies
    14
    Views
    904

    A slight complication! Have you (a) simply...

    A slight complication! Have you (a) simply modified the station by removing the sound, or have you (b) cloned it and modified the clone?

    If (a), no problem as anyone downloading your route will...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4