TrainzUP 2TE10 won't go.
- Thread starter rastis
- Start date
May it be, an other train in your map has derailed while you started session? There is a bug in the script, if any train on the map derails, the script stops its work. So make an attempt to start it at empty route.
PS "автомат управления" (the switch at the middle box under the control board) swould be in on state in both sections, not only in forward one. Also while squeal sound or red light on the control board, press space.
no, this rule isn't supported.
PS "автомат управления" (the switch at the middle box under the control board) swould be in on state in both sections, not only in forward one. Also while squeal sound or red light on the control board, press space.
Last edited:
Make an attept to follow this video - http://www.youtube.com/watch?v=2S5WCYSAlXQ
Richarde57
Active member
Type the kuidnumber in Google and you'll come out at many russian sites. When on a russian site use Google translate to read. Mostly if you found a thread where the missing kuid is offered the file is deleted. Search again and again. I found them after many searches and have everything I need that was missing. Some kuids are in a big rar or zip file. You have to download and unpack. Mostly it is one big cdp file whith lots of kuids in it that are useless for you. Remenber what the cdp has installed in trainz and then delete the kuids you don't need. This seems te be the only way to get your missing kuids.
And beware, you need a good virus and spyware detection program to!
I spend many hours to get that bloody 2TE10M to run but so far no luck. I have them all from TrainzUP. There is one that can drive the way you want. I changed the config.txt of the other locs to get them running. Problem is you have to change the scripts to.
On other russian sites there are also 2TE10M locs you can drive without cabmode but they are not so detailed as the ones on TrainzUP.
Better try the 2TE116 locs, they all have a nice startmenu with cool sounds.
I've changed the smoke of them. First you hear the start engine running, then when the diesel starts, a lot of thick black smoke is coming out for a few seconds.
When the engine runs the black smoke goes to a lightgray and stays that way like a stationairy run. When moving the throttle to drive the smoke increases again.
When the loc stops the stationairy smoke comes back. When shut down the engine the sound and all the smoke is gone.
I would like to have that on every loc in Trainz. It's just so focking stupid to have all the engines running of every loc on the board when they do nothing.
----------------
When you can start one of the 2TE10M locs, just uncouple them and try to drive with the one that runs. They don't need to be coupled to drive just one.
☼ Приятного дня ☼
And beware, you need a good virus and spyware detection program to!
I spend many hours to get that bloody 2TE10M to run but so far no luck. I have them all from TrainzUP. There is one that can drive the way you want. I changed the config.txt of the other locs to get them running. Problem is you have to change the scripts to.
On other russian sites there are also 2TE10M locs you can drive without cabmode but they are not so detailed as the ones on TrainzUP.
Better try the 2TE116 locs, they all have a nice startmenu with cool sounds.
I've changed the smoke of them. First you hear the start engine running, then when the diesel starts, a lot of thick black smoke is coming out for a few seconds.
When the engine runs the black smoke goes to a lightgray and stays that way like a stationairy run. When moving the throttle to drive the smoke increases again.
When the loc stops the stationairy smoke comes back. When shut down the engine the sound and all the smoke is gone.
I would like to have that on every loc in Trainz. It's just so focking stupid to have all the engines running of every loc on the board when they do nothing.
----------------
When you can start one of the 2TE10M locs, just uncouple them and try to drive with the one that runs. They don't need to be coupled to drive just one.
☼ Приятного дня ☼
Last edited:
They are by daemons, you need the cdp named zapcshasti-2Te116.
Thanks fran1 for the info. What I did was substitute some other couplings to get it in game.
I have discovered the following:
In DCC mode nothing happens except the speed control just flickers and returns to zero. If however I select the Drive function in the Driver pop-up, the train starts very slowly and takes about 13 minutes to get up to top speed (74mph) and equally long to stop. I still think there is a problem with the DCC spec in the engine file and will experiment. However the failure to start in ordinary DCC is not a problem there, as substituting an Auran engine file (SD40-2) produced no change although the acceleration was much more normal in Drive.
I have discovered the following:
In DCC mode nothing happens except the speed control just flickers and returns to zero. If however I select the Drive function in the Driver pop-up, the train starts very slowly and takes about 13 minutes to get up to top speed (74mph) and equally long to stop. I still think there is a problem with the DCC spec in the engine file and will experiment. However the failure to start in ordinary DCC is not a problem there, as substituting an Auran engine file (SD40-2) produced no change although the acceleration was much more normal in Drive.
It doesn't exist, unfortunally. This loco has never cross the border of ex-USSR.
By the way the algorithm of its startup is close to 2TE116. The link of the exaple video is on the previous page of the forum (with simple difference connected with the script upgrade - the "machine control" ("автомат управления") lever, should be switched on in both sections; it is situated on the central upright of the control panel).
watch those video till the end.
Last edited:
